What Correx Boards Are Used For
Correx boards are a lightweight fluted plastic sign board used for short term outdoor and indoor display. They are common on boundary fences, vacant plots, building sites, road frontage notices and event entrances because they are easy to carry, quick to fix and affordable when you need several copies. The corrugated core gives the board some body, while the smooth face takes printed graphics clearly for text, arrows and logos.
These boards suit the Boland climate well for temporary use, especially where you need something that can stand up to sun, dust and the odd burst of rain without the cost of a full aluminium panel. They are not a permanent sign choice, but for campaigns that change often they do the job neatly and efficiently. If you need a board up for a few weeks, maybe a few months, correx is often the practical option.
- Estate agent boards for sales and rentals
- Event wayfinding and sponsor boards
- Building and site notices
- Directional signs for parking, entrances and delivery points
- Promotional boards for short campaigns
Sizes, Thicknesses And Finish Options
We make correx boards in common square and rectangular sizes, with custom sizing available if your fence spacing, frame or display area is unusual. Standard boards are often cut to fit estate signage, A4 and A3 notices, or larger panels for roadside visibility. For added strength, we can also produce larger boards with reinforcing where needed, especially if the board will be cable tied to a fence or fixed to a frame.
Most boards are supplied in 3 mm or 5 mm thickness. The thinner sheet is lighter and easy to handle, while the thicker sheet feels a bit firmer for larger signs or windy positions. We can print single sided or double sided, depending on where the message must be seen. Finishing can include rounded corners, drilled holes for tie wire or grommets for neat fixing. If you want the board mounted to another panel or frame, that can be arranged too.
- 3 mm for lighter, short term signage
- 5 mm for larger boards or better stiffness
- Single sided or double sided print
- Drilled holes, grommets or plain cut finish
- Custom sizes to suit fences, stands and frames
Where Correx Works Best In The Boland
Correx boards suit places where the message may change, or where you need a sign that can be removed after the job, sale or event. Estate agents use them for show days, directional arrows and sale boards. Builders use them for site notices, contact boards and safety messages. Schools, clubs and event organisers use them for parking, registration and venue directions. They are also handy for market stalls and temporary promotions outside shops in Paarl, Wellington, Stellenbosch, Franschhoek, Worcester and Malmesbury.
Because the boards are light, they are easier to transport in a bakkie or fit to temporary structures than heavier sign materials. They are a good fit when load shedding or limited site access makes installation time important, since there is no power needed for the board itself. If you need illuminated signage, a different product is better, but for clear daytime communication correx is often the most direct choice.
- Open houses and property direction boards
- Construction and renovation notices
- Roadside and fence mounted event signage
- Temporary shop frontage messages
- Municipal and private site communication
Installation, Fixing And Site Conditions
Correx boards can be installed with cable ties, screws with washers, double sided tape on smooth surfaces, or mounted into a frame. The right fixing depends on wind exposure, board size and how long it must stay in place. On exposed corners or coastal areas nearer to the sea, we often suggest extra fixing points because wind uplift can loosen a board quicker than people expect. A small sign may only need two or four fixings, while a larger board should be secured more fully.
There is no gas or power requirement for the board itself. If the job includes installation on a structure, fence or wall, access and hardware matter more than electricity. For vehicle use, correx is not the usual choice, but it can work as a temporary flat panel or removable notice in some display setups. If the board will be reused, ask for a finish that makes it easier to remove and refit without tearing the fluted structure.
- Cable ties for fence mounted boards
- Washers and screws for timber or walls
- Frames for freestanding or repeated use
- Extra fixing points for windy sites
- Careful placement away from standing water and sharp edges
Care, Reuse And When To Replace It
Correx boards can be reused if they are handled with a bit of care. Store them flat or upright without bending, and keep them out of heavy heat inside a vehicle for long periods, as the surface can mark or soften over time. If a board is used outside for weeks in strong sun, the print may fade sooner than on a more permanent board, so short term use is really where this material performs best.
When a message changes, the board can be reprinted rather than replaced if the size and condition still suit. That helps with estate campaigns, seasonal events and temporary notices that need quick updates. If the board is damaged, warped or the old fixing holes have become weak, it is usually better to replace it rather than trying to patch it up. A clean new board simply looks better from the road and reads properly from a distance, which matters more than people think.
What To Check Before You Order
Before ordering your correx boards, confirm the exact wording, spelling, contact details and arrow directions. Check whether the board will be viewed from one side or both, and whether the message needs to sit high enough to clear grass, parked cars or a fence line. If the sign is for a road frontage or busy junction, think about reading distance and keep the wording short and clear.
It also helps to know the final size, how it will be fixed, and whether the board must fit an existing frame or municipal restriction. For property and site notices, make sure the wording matches any permit or estate rules that apply. If you need several identical boards, ask for a consistent layout from the start so the set looks neat across all sites. A quick artwork check now saves time later, and avoids little errors that stand out once the boards are up.
- Exact wording and contact details
- Single sided or double sided viewing
- Final size and mounting method
- Site exposure to wind, sun and rain
- Any permit, estate or venue rules
Key facts
| Material | Fluted polypropylene correx board |
|---|---|
| Thickness | 3 mm or 5 mm |
| Single sided or double sided | |
| Typical use | Temporary signs for estate, event and site notices |
| Finish options | Cut to size, rounded corners, drilled holes, grommets |
| Installation | Cable ties, screws with washers, tape or frame mounting |
